Skip to content

Upgrade Firmware

Current Version of Coldcard Firmware

For Mk4 (our flagship!): v5.3.0 for Mk4 released May 6, 2024.

For Q (the new kid): v1.2.0Q for Q released May 6, 2024.

Find all available downloads here.

Video: How to Upgrade Firmware

Learn how to upgrade here but start with one of those files.

Shared Improvements: Mk4 and Q#

COLCARD Mk4 and COLDCARD Q now share the same codebase.

  • Enhancement: Add Nunchuk and Zeus options to Export Wallet
  • Enhancement: View Identity shows temporary seed active at the top
  • Enhancement: Can specify start index for address explorer export and browsing
  • Enhancement: Allow unlimited index for BIP-85 derivations. Must be enabled first in Danger Zone
  • Change: Passphrase menu item is no longer offered if BIP39 passphrase already in use. Use Restore Master with ability to keep or purge current passphrase wallet settings.
  • Change: Removed ability to add passphrase to master seed if active temporary seed.
  • Change: Wipe LFS during Lock Down Seed and Destroy Seed
  • Bugfix: Do not allow non-ascii or ascii non-printable characters in multisig wallet name
  • Bugfix: Brick Me option for If Wrong PIN caused yikes.
  • Bugfix: Properly handle and finalize framing error response in USB protocol.
  • Bugfix: Handle ZeroSecretException for BIP39 passphrase calculation when on temporary seed without master secret
  • Bugfix: Saving passphrase on SD Card caused a freeze that required reboot
  • Bugfix: Properly verify signed armored message with regtest address
  • Bugfix: Create ownership file when generating addresses export CSV
  • Recovery SD Card image building moved into its own repo: github.com/Coldcard/recovery-images

Mk4 Specific Changes#

5.3.0 - 2024-05-06#

  • Enhancement: When providing 12 or 18 word seed phrase, valid final word choices are presented in a new menu.
  • Enhancement: Move dice rolls (for generating master seed) to Advanced submenu.
  • Enhancement: Using "Verify Address" in NFC Tools menu, allows entry of a payment address and reports if it is part of a wallet this Coldcard knows the key for. Includes Multisig and single sig wallets.
    • searches up to the first 1528 addresses (external and change addresses)
    • stores data as it goes to accelerate future uses
    • worst case, it can take up to 2 minutes to rule out an address, but after that it is fast!
  • Bugfix: Constant AFC_BECH32M incorrectly set AFC_WRAPPED and AFC_BECH32.
  • Bugfix: Fix inability to activate Duress Wallet as temporary seed when master seed is 12 words.
  • Bugfix: Yikes when using BIP39 passphrase with temporary seed without master seed set.
  • Bugfix: v1 and v2 QRs too small and not readable (fixed)
  • Bugfix: Show indexes for full range of addresses we are able to generate during QR display.
  • Tweak: Force default HW settings (USB,NFC,VDisk OFF) after clone/backup is restored.
  • Tweak: Cleanup in NFC code: repeated messages, "Unable to find data expectd in NDEF", removed.
  • Bootrom version bump: 3.2.0 released with no functional changes except those shared with Q.

Q Specific Changes#

1.2.0Q - 2024-05-06#

  • Enhancement: Allow export of multisig XPUBs via BBQr
  • Enhancement: Import multisig via QR/BBQr - both legacy COLDCARD export and descriptors supported
  • Enhancement: Status bar text is sharper now
  • Enhancement: Added ability to write signed PSBT/txn to lower (B) SD slot when both cards inserted
  • Bugfix: Fullscreen display of v23 and v24 QRs were too dense and hard to read
  • Bugfix: Battery idle timeout also considers last progress bar update
  • Bugfix: Allow Send Password (keystrokes) of capital letters of alphabet
  • Bugfix: Pressing SYM+SHIFT was toggling CAPS continuously. Now toggles once only
  • Bugfix: Restrict keys that can be pressed during seed entry after final word inserted

🧙 Edge Version 6.2.2X [development purposes]#

Find binary here and view release notes. Advanced features currently in Edge:

  • now with latest Mk4 features from 5.2.2 including Seed Vault and Temporary Seed enhancements
  • Miniscript and MiniTapscript support (see docs/miniscript.md)
  • New Enhancement: Tapscript up to 8 leafs
  • Taproot spending, signing, multisig.
  • BIP-129 Bitcoin Secure Multisig Setup (BSMS)
  • New USB commands to support Miniscript and Tapscript.

This preview version of firmware has not yet been qualified and tested to the same standard as normal Coinkite products. It is recommended only for developers and early adopters and experimental use. DO NOT use for large Bitcoin amounts.

Older releases and their changes are listed here, the full source code, hardware details, and much more can be found in our repository on github. Other downloads are listed here.

Upgrading Your COLDCARD's Firmware#

Mark 1 Firmware Limit

Do not attempt to upgrade a Mark 1 COLDCARD beyond firmware version 3.0.6 (2019-12-19T1623-v3.0.6)!

Mark 1 hardware is no longer supported. Newer firmware versions will completely brick a Mark 1 COLDCARD. Look for the revision (Mark 1, Mark 2, Mark 3) on the back of your COLDCARD before you begin upgrading.

Introduction#

About Upgrades#

Stay up to date on firmware releases - follow our Twitter account @COLDCARDwallet, or bookmark the Coinkite Blog.

Firmware upgrades provide new features, enhancements, bugfixes, and the latest security updates to your COLDCARD.

Firmware upgrade files have a .dfu file extension and should be at least 800 KB in size. We use the abbreviation 20...-coldcard.dfu to represent the full firmware file name. Make sure to use the full file name in your commands.

COLDCARDs only load and run files signed by a Coinkite Inc. approved key.

Upgrade Menu#

The Upgrade menu allows you to load an upgrade .dfu file from a microSD card.

advanced menu

Upgrade Menu Options#

Show Version displays the version numbers of the firmware currently loaded on your COLDCARD.

From MicroSD lets you start the firmware upgrade process.

Bless Firmware marks the firmware upgrade as approved by the main PIN holder. This step is necessary if your COLDCARD loses power before the upgrade is confirmed.

Alternate Upgrade Methods#

These instructions use a microSD card to upgrade the firmware. You can also upgrade by using the command-line tool or the Electrum plugin. On the Mk4, if USB drive emulation is enabled, you can simply copy the dfu file onto the COLDCARD.

Downgrading Firmware and Older Versions#

Downgrading to an older firmware version is discouraged and may be blocked depending on your current firmware. Some firmware releases will prevent the bootloader from accepting older versions due to bugs or security issues found in older firmware. A limited selection of previously released firmware is available here.

Upgrade Procedure Using MicroSD#

What You'll Need#

  • One COLDCARD
  • microSD card (up to 32 GB capacity, FAT32 or FAT12 format)
  • Micro USB cable, power-only preferred
  • Power source for Micro USB cable, COLDPOWER or AC to USB adapter preferred
  • Internet-capable device for downloading and saving files

What You'll Do#

Check Your Current COLDCARD Firmware Version#
  1. Connect the COLDCARD to a power source with the Micro USB cable to turn it on.
  2. Enter your PIN to unlock the COLDCARD.
  3. Select Advanced > Upgrade > Show Version.
  4. Compare the version shown on the screen with the latest version shown on coldcard.com/docs/upgrade. If your COLDCARD doesn't have the latest firmware version, it's time to upgrade.
Get the Latest Firmware#
  1. Go to coldcard.com/docs/upgrade if you're not already here. The latest firmware release will be at the top of the page.
  2. Save the 20...-coldcard.dfu file to your microSD card or a folder on your computer.
  3. Decide whether you will verify the firmware's hash and signature (strongly recommended) or load the firmware on your COLDCARD without verification.
  4. Verifying? Go to the verification instructions.
Load the Latest Firmware on your COLDCARD#
  1. Save the 20...-coldcard.dfu file to your microSD card if you haven't done so already and eject the card once the file is saved.
  2. Make sure your COLDCARD is turned on and unlocked.
  3. Select Advanced > Upgrade > From MicroSD.
  4. Press OK (✔) on your COLDCARD when you are prompted to pick the firmware image.
  5. Select the firmware file.
  6. The screen will say "Loading. . .". Be patient, this process takes time.

Note: When the screen changes to Verifying, the red LED will light up and stay lit until the firmware upgrade is complete. The red CAUTION LED lets you know changes are being made or have been made to your COLDCARD. If the COLDCARD is turned off after the new firmware is installed but before the first successful login, you will need to bless the firmware to turn the red LED off.

Do not turn off power to the Mk4 during it's 15-second upgrade process. Doing so will put it into a special recovery mode which requires a specially-prepared MicroSD card to be used.

Confirm and Finish Upgrade#
  1. Enter your PIN prefix when prompted after the COLDCARD reboots.
  2. Verify whether or not you recognize the two words displayed on the screen. These words are hardware-specific to ensure you have the correct device. A different COLDCARD will display different words.
  3. Enter the rest of your PIN when prompted.
  4. The COLDCARD will perform another verification and the green GENUINE LED will light up.
  5. Inspect your upgrade by selecting Advanced > Upgrade > Show Version. The firmware version you loaded will be displayed. You have successfully upgraded your COLDCARD's firmware!
Video Tutorial#

Watch Max Hillebrand perform the firmware upgrade and verification process using Debian and a Mark 2 COLDCARD.

Optional Steps#

Red LED Lit After Restart? Bless the Firmware#

The red CAUTION LED is a safety feature warning you of unconfirmed changes to your COLDCARD. Only the main PIN holder can confirm changes. If you load new firmware and turn off the device before confirming the upgrade, the CAUTION LED will be lit the next time you turn on your COLDCARD. Blessing the firmware tells the COLDCARD that you are aware of and approve of the firmware upgrade.

  1. Follow the prompts on the screen to log in to your COLDCARD.
  2. Select Advanced > Upgrade > Bless Firmware.
  3. The screen will say Verifying the green GENUINE LED will light up confirming your approval of the new firmware.

Once the firmware is blessed, your COLDCARD will light up the green LED on future startups.

Don't Trust. Verify the Firmware#

Verifying the firmware's hash and signature requires intermediate to advanced computer skills. It uses extra tools and adds steps, but if you use a COLDCARD, you're probably security-conscious. In that case, you may find the extra effort to be worth the peace of mind you'll get from knowing your firmware is safe and correct.

Note: PGP signature verification requires GPG. Debian and other Linux distributions include GPG. Mac and Windows users who have not already installed GPG will need to do so. Operating system-specific instructions contain links to tool downloads.

Verifying on Mac#

These instructions use GPG Keychain, a component of the GPG Suite from GPGTools.

You can also follow along with our video tutorial, How to Verify COLDCARD's Firmware.

Confirm the Hash

  1. Open signatures.txt so you can view its contents.
  2. Open Terminal, navigate to the directory where you saved the firmware and use the command shasum -a256 20...-coldcard.dfu.
  3. Resize or reposition the windows so you can see both the Terminal and signatures.txt file at the same time.
  4. Compare the output values in Terminal with the line of text in the signatures.txt file next to the firmware version you saved. The hash is confirmed if the values are the same.

Verify the PGP Signature

  1. Save the signatures.txt file in the same location as the new firmware file.
  2. Save the public key 4589779ADFC14F3327534EA8A3A31BAD5A2A5B10 as a new-pubkey.txt file in the same location as the firmware and signatures.txt files.
  3. Open GPG Keychain.
  4. Click the Import button and navigate to new-pubkey.txt. Select the file and click Open. A pop-up message should appear saying "Import successful".
  5. Open Terminal and enter gpg --verify signatures.txt.
  6. The output in Terminal should include Good signature from.... It is normal to see WARNING: This key is not certified with a trusted signature! gpg: There is no indication that the signature belongs to the owner. You may ignore the warning, the signature is verified.

Once the hash and signature are verified, load the latest firmware on your COLDCARD.

Verifying on Linux#

Confirm the Hash

  1. Open signatures.txt so you can view its contents.
  2. Use the command line to navigate to the directory where you saved the firmware and enter the command sha256sum 20...-coldcard.dfu.
  3. Resize or reposition the windows so you can see both the command output and signatures.txt file at the same time.
  4. Compare the output value from the command with the line of text in the signatures.txt file next to the firmware version you saved. The hash is confirmed if the values are the same.

Verify the PGP Signature

  1. Save the signatures.txt file in the same location as the new firmware file.
  2. On the command line, enter curl "https://keyserver.ubuntu.com/pks/lookup?op=get&search=0xA3A31BAD5A2A5B10" | gpg --import to import the public key.
  3. Next, enter gpg --verify signatures.txt to verify the file's signature versus its content.
  4. The command output should include Good signature from.... It is normal to see WARNING: This key is not certified with a trusted signature! gpg: There is no indication that the signature belongs to the owner. You may ignore the warning, the signature is verified.

Once the hash and signature are verified, load the latest firmware on your COLDCARD.

Verifying on Windows#

These instructions use Kleopatra, which is a part of Gpg4win (GNU Privacy Guard for Windows). You only need the GnuPG Privacy Guard and Kleopatra components to verify the PGP signature.

Kleopatra requires you to have an OpenPGP signature to complete verification. If you don't have a signature to import, you can make one in Kleopatra.

Confirm the Hash

  1. Open signatures.txt so you can view its contents.
  2. Open Command Prompt and enter certutil -hashfile C:\..\20...-coldcard.dfu SHA256, where C:\..\20...-coldcard.dfu is the full path to the saved firmware file.
  3. Resize or reposition the windows so you can see both the Command Prompt output and signatures.txt file at the same time.
  4. Compare the output values in Command Prompt with the line of text in the signatures.txt file next to the firmware version you saved. The hash is confirmed if the values are the same.

Verify the PGP Signature

  1. Save the text from signatures.txt with an .asc file extension in the same location as the saved firmware file. Do not save the file as .txt, Kleopatra will not recognize it.
  2. Save the public key 4589779ADFC14F3327534EA8A3A31BAD5A2A5B10 as an .asc file in the same location as the firmware and signatures.asc files.
  3. Open a browser and go to keybase.io/DocHex. Click on the text next to the key icon to open the public key window. You will need this window for a later step.
  4. Open Kleopatra and click Import....
  5. Navigate to the public key .asc file and open it.
  6. You will be asked to check the fingerprint of the file and given suggested options. The Keybase public key window is the trusted website. Click Yes.
  7. A Certify Certificate window will show the file's fingerprint, your certification, and the fingerprint's owner - in this case, Peter D. Gray. Resize or reposition the Certify Certificate window and the browser window opened in step 3 so you can see them both at the same time.
  8. Make sure the fingerprints in each window match and click Certify. If you have a passphrase on your certificate, you'll be asked to enter it. A pop-up box should appear saying, "Certification successful." Click Ok.
  9. Click Decrypt/Verify... and open signatures.asc.
  10. Kleopatra will verify the signature. You may save or discard the file Kleopatra generates, it is not needed. The signature is verified.

Once the hash and signature are verified, load the latest firmware on your COLDCARD.